Disclaimer:The following init.d scripts assume some linux knowledge and that your Synology NAS device has been bootstrapped allowing you to install the required dependancies using ipkg.
These instructions do not describe how to download, install or configure SABnzbd, Sickbeard or CouchPotato. All init.d scripts have been tested and work fine on a Synology 411+ running DSM 3.1. All init.d scripts expect certain packages to be installed in order to work correctly.
These scripts should be placed in /opt/etc/init.d/ and be given the same filenames and permissions as shown below.
All init.d scripts require some values to be defined by you in order to work correctly.
Required Packages
- openssl
- py26-cheetah
- py26-openssl
- python26
- wget
SABnzbd – /opt/etc/init.d/S99sabnzbd.sh (rwxr-xr-x)
Download: S99sabnzbd.sh
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 | #!/bin/sh # # Synology DSM init script for SABnzbd # Requires: sabnzbd # python # wget # # Configured Variables: # PYTHON_EXEC="/opt/bin/python2.6" SABNZBD_EXEC="/opt/share/sabnzbd/SABnzbd.py" SABNZBD_PORT="9200" SAB_API_KEY="YOUR API KEY GOES HERE" SAB_INI_FILE="ABSOLUTE PATH TO sabnzbd.ini" # Begin script # case "$1" in start) PATH=$PATH:/opt/bin printf "%-30s" "Starting SABnzbd" ${PYTHON_EXEC} ${SABNZBD_EXEC} -s 0.0.0.0:${SABNZBD_PORT} -f ${SAB_INI_FILE} -d printf "[%4s]\n" "done" ;; stop) printf "%-30s" "Stopping SABnzbd" /opt/bin/wget -q --delete-after "http://127.0.0.1:${SABNZBD_PORT}/shutdown?session=${SAB_API_KEY}" printf "[%4s]\n" "done" ;; *) echo "Usage: $0 {start|stop}" exit 1 esac exit 0 |
SickBeard – /opt/etc/init.d/S99sickbeard.sh (rwxr-xr-x)
Download: S99sickbeard.sh
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 | #!/bin/sh # # Synology DSM init script for SickBeard # Requires: sickbeard # python # wget # # Configured Variables: # PYTHON_EXEC="/opt/bin/python2.6" SICKBEARD_EXEC="/opt/share/sickbeard/SickBeard.py" SICKBEARD_PORT="9201" # Begin script # case "$1" in start) printf "%-30s" "Starting SickBeard" nohup ${PYTHON_EXEC} ${SICKBEARD_EXEC} -q -d > /dev/null 2>&1 & printf "[%4s]\n" "done" ;; stop) printf "%-30s" "Stopping SickBeard" /opt/bin/wget -q --delete-after "http://127.0.0.1:${SICKBEARD_PORT}/home/shutdown/" printf "[%4s]\n" "done" ;; *) echo "Usage: $0 {start|stop}" exit 1 esac exit 0 |
CouchPotato – /opt/etc/init.d/S99couchpotato.sh (rwxr-xr-x)
Download: S99couchpotato.sh
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 | #!/bin/sh # # Synology DSM init script for CouchPotato # Requires: couchpotato # python # wget # # Configured Variables: # PYTHON_EXEC="/opt/bin/python2.6" COUCHPOTATO_EXEC="/opt/share/couchpotato/CouchPotato.py" COUCHPOTATO_PORT="9203" # Begin script # case "$1" in start) printf "%-30s" "Starting CouchPotato" ${PYTHON_EXEC} ${COUCHPOTATO_EXEC} -d & printf "[%4s]\n" "done" ;; stop) printf "%-30s" "Stopping CouchPotato" /opt/bin/wget -q --delete-after "http://127.0.0.1:${COUCHPOTATO_PORT}/config/exit/" printf "[%4s]\n" "done" ;; *) echo "Usage: $0 {start|stop}" exit 1 esac exit 0 |
If you find this helpful or found a problem with any of the scripts let me know in the comments section below.
This is a demo of the flickr plugin
Well it was time to replace that old skylight in our cottage so I collected all the supplies I’d need and set to work. After two days of working non stop I got the old window out, the hole reframed and widened. Removed some of the old shingles around the hole and put the new skylight in place. After careful reading of the instructions re-shingling
and flashing went fairly well.
Unfortunately I was unable to fix the two short shingles from the original window. They wrapped up over the peak and would have involved a lot more shingle tear out. So for now I left them intact.
Now its back to work and rest up for the next project.
